LG OLED65C1PUB VESA Size & Mount Fit
Quick answer
The LG OLED65C1PUB uses a 300×200 mm VESA pattern (M6 screws). Screw spec: M6 - length not published by LG. The OLED65C1PUB weighs 52.9 lb (24 kg) without the stand. Any mount rated for VESA 300×200 or larger and at least 70 lb will fit the OLED65C1PUB. Verified against the LG documentation — see source below.
OLED65C1PUB mounting specs
| VESA pattern | 300×200 mm (11.8×7.9 in) |
|---|---|
| Screw thread | M6 |
| Screw length | M6 - length not published by LG; hand-test with the mount's shortest M6 bolts and do not force |
| Weight without stand | 52.9 lb (24 kg) |
| Stand width | 39.3 in — stand footprint |
| Screen size | 65 in |
| Model year | 2021 |
| Series | C1 OLED |
| Known aliases | OLED65C1AUB |
| Source | Manufacturer documentation |
At 52.9 lb this is one of the heaviest 300x200-pattern TVs around - the small pattern concentrates load, so use a mount rated 70 lb or more.
Among the 21 verified 65-inch TVs in our database, the OLED65C1PUB is #18 lightest of 21 at 52.9 lb — the 65-inch range here runs 30.9 to 56.4 lb. Within LG, the OLED55C2PUA, OLED65C2PUA, OLED42C2PUA share the OLED65C1PUB's 300×200 mm pattern.
Mounts that fit the OLED65C1PUB
Filtered from our mount database: pattern covers 300×200 mm, rating is at least 70 lb (20% margin over the OLED65C1PUB's 52.9 lb), and the 65-inch screen is within the listed range.
EchoGear EGLF2 Full Motion
Smooth dual-arm full motion with 22 in of extension for corner installs.
Supports VESA 100×100 up to 600×400 mm and 125 lb — clears the OLED65C1PUB's 300×200 mm / 52.9 lb.
Wall: 16-in dual stud required
EchoGear EGLT1 Tilting
Deep 15-degree tilt for bedroom and above-fireplace placements.
Supports VESA 200×200 up to 600×400 mm and 125 lb — clears the OLED65C1PUB's 300×200 mm / 52.9 lb.
Wall: 16-in dual stud required
EchoGear EGLL1 Low-Profile Fixed
Ultra-low-profile fixed mount that keeps the TV about an inch off the wall.
Supports VESA 200×200 up to 600×400 mm and 125 lb — clears the OLED65C1PUB's 300×200 mm / 52.9 lb.
Wall: 16-in dual stud required
Mount-It! MI-509B Ceiling
Ceiling mount for larger screens with tilt and telescoping height.
Supports VESA 100×100 up to 600×400 mm and 110 lb — clears the OLED65C1PUB's 300×200 mm / 52.9 lb.
Wall: lag-bolt into a ceiling joist per the manual
Pipishell PISF1 Fixed
Heavy-duty fixed plate for big panels; sits low and rigid.
Supports VESA 200×200 up to 600×400 mm and 132 lb — clears the OLED65C1PUB's 300×200 mm / 52.9 lb.
Wall: 16-in dual stud required
Not sure between two of them? Run the Will It Fit checker for a verdict with reasons.
Screws & spacers for the OLED65C1PUB
The OLED65C1PUB takes M6 bolts: M6 - length not published by LG; hand-test with the mount's shortest M6 bolts and do not force. A bolt longer than the documented spec can bottom out against internal components and damage the panel — thread a screw in by hand first and confirm it seats before mounting the TV.
If your mount's hardware kit doesn't include the right length, a universal TV hardware kit covers M4–M8 in common lengths. More detail in the screw size guide.
Standing the OLED65C1PUB on furniture instead?
Per LG's documentation, the OLED65C1PUB's factory stand is 39.3 in wide — plan a console at least 42 in wide. The panel can overhang the furniture; the stand cannot.
Furniture narrower than 42 in? A universal pedestal stand bolts into the same 300×200 mm VESA holes (M6 screws) and stands on a single center column — the usual fix instead of replacing the console. Check its weight rating against the OLED65C1PUB's 52.9 lb.
Replacement remote for the OLED65C1PUB
LG Magic Remote (2021) — part number AN-MR21GA — is the matching remote for the OLED65C1PUB. Bluetooth RF Magic Remote with voice mic and motion pointer; 2 AA batteries. LG's own 2021 Magic Remote guide (p/n AGF30136002) covers the whole 2021 lineup - C1/G1/A1/B1 OLED plus QNED/NANO/UP75/UP80.
Full compatibility list, substitutes and ordering advice: AN-MR21GA remote page. Order by the part number, not the TV size — one remote covers the platform. All LG remotes are on the brand hub.
Double-check before buying
- Remove any plastic hole plugs on the back panel and confirm all 4 threaded holes are present and undamaged.
- Measure hole spacing center-to-center in millimeters — you should get 300 mm across and 200 mm vertically.
- Compare the model number on the back-panel sticker with the one on this page (OLED65C1PUB) — retail variants can differ.
How to verify yourself
- Lay the TV screen-down on a soft, flat surface and locate the 4 threaded holes on the back.
- Measure horizontally between the centers of the upper holes, then vertically between an upper and a lower hole — in millimeters.
- Match the two numbers to a standard pattern (for the OLED65C1PUB: 300×200 mm). Full walkthrough with photos of what to avoid: how to measure VESA.
Frequently asked questions
What VESA pattern does the LG OLED65C1PUB use?
The LG OLED65C1PUB uses a 300×200 mm VESA pattern — 300 mm between hole centers horizontally and 200 mm vertically (about 11.8×7.9 in). Any bracket whose supported range covers 300×200 mm will line up. Confirm on the back panel before ordering, since retail variants of a series occasionally differ.
What size screws does the OLED65C1PUB need for wall mounting?
The OLED65C1PUB takes M6 metric screws. Documented length: M6 - length not published by LG; hand-test with the mount's shortest M6 bolts and do not force. A bolt that is too long can bottom out and damage the panel or internals, so verify thread depth on the OLED65C1PUB with a hand-tightened test screw before torquing anything down.
How much does the OLED65C1PUB weigh without the stand?
The OLED65C1PUB weighs 52.9 lb (24 kg) without the stand or cables. For a 20% safety margin, pick a mount rated for at least 70 lb. Anchoring matters as much as the rating: at this weight, one properly hit stud is usually enough, but follow your mount's instructions.
Will a 400×400 mount fit the OLED65C1PUB?
A bracket sold as 400×400-only will not line up with the OLED65C1PUB's 300×200 mm holes. Most 400×400 mounts, however, support a range of patterns — if the spec sheet lists 300×200 mm, it fits directly. If not, a VESA adapter plate (300×200→400×400) bridges the difference; see our adapter guide.
How wide is the OLED65C1PUB's stand?
Per the manufacturer's documentation, the OLED65C1PUB's factory stand is about 39.3 in wide. Plan at least 42 in of flat, level surface: the panel can overhang the furniture, the stand cannot. If your console is narrower, a universal pedestal stand bolts into the 300×200 mm VESA holes instead.
What replacement remote works with the OLED65C1PUB?
LG Magic Remote (2021) (part AN-MR21GA) is the matching remote for the OLED65C1PUB. Bluetooth RF Magic Remote with voice mic and motion pointer; 2 AA batteries. LG's own 2021 Magic Remote guide (p/n AGF30136002) covers the whole 2021 lineup - C1/G1/A1/B1 OLED plus QNED/NANO/UP75/UP80. Order by the part number rather than by TV size — one remote covers the whole platform.
Can the OLED65C1PUB be mounted on a full-motion bracket?
Yes. At 52.9 lb, the OLED65C1PUB is within range of full-motion arms rated 70 lb or higher — 3 full-motion mount(s) in our database clear it. Articulating arms add leverage on the wall, so stud anchoring per the mount manufacturer's instructions is more important than with fixed brackets.