Hisense 65A6H VESA Size & Mount Fit
Quick answer
The Hisense 65A6H uses a 400×300 mm VESA pattern (M6 screws). Screw spec: M6. The 65A6H weighs 36.4 lb (16.5 kg) without the stand. Any mount rated for VESA 400×300 or larger and at least 50 lb will fit the 65A6H. Verified against the Hisense documentation — see source below.
65A6H mounting specs
Archived Hisense USA page (UPC 888143012612): VESA 400x300, M6, 36.4 lb without stand (36.8 lb with). The 65 in A6H jumps to 400x300 while the 50/55 in siblings keep a tall 200x300 print - one bracket does not serve a mixed pair. Hisense publishes no numeric stand width for this model; its QSG shows two-position feet.
Weight vs. required mount rating
Among the 23 verified 65-inch TVs in our database, the 65A6H is #6 lightest of 23 at 36.4 lb — the 65-inch range here runs 30.9 to 56.4 lb. Within Hisense, the 65U6K, 55U8K share the 65A6H's 400×300 mm pattern.
Mounts that fit the 65A6H
Filtered from our mount database: pattern covers 400×300 mm, rating is at least 50 lb (20% margin over the 65A6H's 36.4 lb), and the 65-inch screen is within the listed range.
EchoGear EGLF2 Full Motion
Smooth dual-arm full motion with 22 in of extension for corner installs.
Supports VESA 100×100 up to 600×400 mm and 125 lb — clears the 65A6H's 400×300 mm / 36.4 lb.
Wall: 16-in dual stud required
EchoGear EGLT1 Tilting
Deep 15-degree tilt for bedroom and above-fireplace placements.
Supports VESA 200×200 up to 600×400 mm and 125 lb — clears the 65A6H's 400×300 mm / 36.4 lb.
Wall: 16-in dual stud required
EchoGear EGLL1 Low-Profile Fixed
Ultra-low-profile fixed mount that keeps the TV about an inch off the wall.
Supports VESA 200×200 up to 600×400 mm and 125 lb — clears the 65A6H's 400×300 mm / 36.4 lb.
Wall: 16-in dual stud required
Mount-It! MI-509B Ceiling
Ceiling mount for larger screens with tilt and telescoping height.
Supports VESA 100×100 up to 600×400 mm and 110 lb — clears the 65A6H's 400×300 mm / 36.4 lb.
Wall: lag-bolt into a ceiling joist per the manual
Pipishell PISF1 Fixed
Heavy-duty fixed plate for big panels; sits low and rigid.
Supports VESA 200×200 up to 600×400 mm and 132 lb — clears the 65A6H's 400×300 mm / 36.4 lb.
Wall: 16-in dual stud required
Not sure between two of them? Run the Will It Fit checker for a verdict with reasons.
Screws & spacers for the 65A6H
The 65A6H takes M6 bolts: M6 per Hisense's spec page; the A6H quick setup guide calls for 9.5-11.5 mm thread engagement from the rear cover on 65/75 in - length varies by bracket. A bolt longer than the documented spec can bottom out against internal components and damage the panel — thread a screw in by hand first and confirm it seats before mounting the TV.
If your mount's hardware kit doesn't include the right length, a universal TV hardware kit covers M4–M8 in common lengths. More detail in the screw size guide.
Replacement remote for the 65A6H
Hisense Google TV Remote (OEM) — part number T299843 — is the matching remote for the 65A6H. Bluetooth + IR voice remote with Google TV shortcut keys; 2 AAA batteries. Hisense USA's own parts store lists this OEM remote for the U6K A6H and A65K lines explicitly (55/65/75U6K and 43-75 in A-series).
Full compatibility list, substitutes and ordering advice: T299843 remote page. Order by the part number, not the TV size — one remote covers the platform. All Hisense remotes are on the brand hub.
Double-check before buying
- Remove any plastic hole plugs on the back panel and confirm all 4 threaded holes are present and undamaged.
- Measure hole spacing center-to-center in millimeters — you should get 400 mm across and 300 mm vertically.
- Compare the model number on the back-panel sticker with the one on this page (65A6H) — retail variants can differ.
How to verify yourself
- Lay the TV screen-down on a soft, flat surface and locate the 4 threaded holes on the back.
- Measure horizontally between the centers of the upper holes, then vertically between an upper and a lower hole — in millimeters.
- Match the two numbers to a standard pattern (for the 65A6H: 400×300 mm). Full walkthrough with photos of what to avoid: how to measure VESA.
Frequently asked questions
What VESA pattern does the Hisense 65A6H use?
The Hisense 65A6H uses a 400×300 mm VESA pattern — 400 mm between hole centers horizontally and 300 mm vertically (about 15.7×11.8 in). Any bracket whose supported range covers 400×300 mm will line up. Confirm on the back panel before ordering, since retail variants of a series occasionally differ.
What size screws does the 65A6H need for wall mounting?
The 65A6H takes M6 metric screws. Documented length: M6 per Hisense's spec page; the A6H quick setup guide calls for 9.5-11.5 mm thread engagement from the rear cover on 65/75 in - length varies by bracket. A bolt that is too long can bottom out and damage the panel or internals, so verify thread depth on the 65A6H with a hand-tightened test screw before torquing anything down.
How much does the 65A6H weigh without the stand?
The 65A6H weighs 36.4 lb (16.5 kg) without the stand or cables. For a 20% safety margin, pick a mount rated for at least 50 lb. Anchoring matters as much as the rating: at this weight, one properly hit stud is usually enough, but follow your mount's instructions.
Will a 600×400 mount fit the 65A6H?
A bracket sold as 600×400-only will not line up with the 65A6H's 400×300 mm holes. Most 600×400 mounts, however, support a range of patterns — if the spec sheet lists 400×300 mm, it fits directly. If not, a VESA adapter plate (400×300→600×400) bridges the difference; see our adapter guide.
What replacement remote works with the 65A6H?
Hisense Google TV Remote (OEM) (part T299843) is the matching remote for the 65A6H. Bluetooth + IR voice remote with Google TV shortcut keys; 2 AAA batteries. Hisense USA's own parts store lists this OEM remote for the U6K A6H and A65K lines explicitly (55/65/75U6K and 43-75 in A-series). Order by the part number rather than by TV size — one remote covers the whole platform.
Can the 65A6H be mounted on a full-motion bracket?
Yes. At 36.4 lb, the 65A6H is within range of full-motion arms rated 50 lb or higher — 3 full-motion mount(s) in our database clear it. Articulating arms add leverage on the wall, so stud anchoring per the mount manufacturer's instructions is more important than with fixed brackets.